Photo Frame Pin Ornament Wood Art Stamp

Photo Frame Pin Ornament Wood Art Stamp Rubber Stamp Make and decorate a frame pin ornament, using this stamp as a pattern! Press stamp onto paper card stock or fabric! Hang frame like a pin with military clutch pin back through hole at top on back, that with ribbon, also allows frame to hang like an ornament! For photo size 3/4" wide x 1 1/4" height photo FRAME DIMENSIONS: 1 3/8 wide by 1 3/4 + 1/16 height frame 1 3/8" wide by 1 7/8" height frame 3/4" wide x 1 1/4" height photo 5/8" pw wide x 1 1/8" pw height - pw means "picture window" use 1/8" wide diameter hole puncher with long reach ____________ Instructions: Press stamp onto letter size sheet of paper card stock, or the back of wallpaper, gift wrap, special paper, or front of fabric - up to 4 frame pin ornaments per letter size sheet of paper, 16 frame pin ornaments on "fat quarter" or 22x18" fabric For fabric, iron Therm o Web HeatnBond iron on, paper back, interfacing adhesive to back of fabric, use stamp design as a pattern For paper, can seal with fixative or press 3 mil gauge self laminating sheet to front, optional for back Cut out panels, include the outer and inner flaps, to fold under. Cut along lines to cut away excess at outer, and into inner corners, folding flaps under. Hole punch all circles with 1/8" diameter quality hole puncher. Place panel 2 over panel 3, line patterns facing in, thread 1/8" wide by 15" long, in and out of holes, do in both directions, knot on both sides, trim ribbon tails, glue down. Place and attach / glue / sew panel 1 over panel 2, gluing / sewing inner edge of picture windows together. Glue or sew outer edges, making sure to leave opening for photo and protective sleeve (acid free / photo safe sheet protector page, cut to size of photo). Glue or sew 3 other sides. Place easel back panel or panel 4 over back of panel 3, print side facing up. Glue or sew down outer edge, making sure to leave opening between panels 2 & 3. Sew from right middle then around to top middle, stop, move to other side of hole, and sew top left, around to left middle, stop, move around hole, and sew from left middle under hole to bottom left in to middle. Stop. Leave opening for ribbon tail to tuck inside pocket at bottom right corner. Make strut leg: Cut out top and bottom of both front and back strut leg panels. Fold under flaps. Cut out top, 5 sided strut leg clear piece pattern, below panels 1 & 2, with long side facing up towards panels 1 & 2. Use this for the bendable, clear piece, sandwiched between the front and back strut leg panels, with spacer between, for strut leg to be bendable. Place top and bottom of back strut leg panels face down, align clear piece over both, showing space between, fitting inside the edges of both top & bottom back strut leg panels, glue down. Glue top strut leg of front strut leg on top. Place ribbon 3/8" or 9mm wide within vertical edge of strut leg over clear bendable piece, glue down. Glue bottom strut leg of front strut leg on bottom. Place finished, bendable strut leg panel over panel 4 or easel back, align bottom right corner edges. Clip or pin in place, to hold in place. Flip back top of strut leg, add glue, flip and press or sew down. Stand frame, pitch out leg, with ribbon tail under frame, out and in front, pin where the ribbon meets the bottom of the frame, to mark, trim excess ribbon. Tuck ribbon inside pocket at bottom right corner of frame, adjust so the frame stands on its out, place glue inside ribbon pocket at bottom right corner. ___________ Supplies: 5x4" paper or fabric, to stamp the stamp pattern onto the front ribbon 1/8" or 3mm wide by 15" long ribbon 3/8" or 9mm wide by 6" long ribbon another 1/8" or 3mm wide by 1 foot long - for hanging as ornament 1 acid free / photo safe sheet protector page for photo sleeve and bendable strut leg piece hot glue sticks 1-2 low temp Cool Touch superbonder or AdTech super low temp glue gun hole puncher pointy, small, preferably embroidery or Fiskars nonstick fabric scissors fabric scissors and/or scissors - paper trimmer optional thin 3 mil gauge self laminating sheet optional thread optional machine needle 100/16 or 110/18 size long stitch lengths, and sew slow - optional military clutch pin back Thank you! Kristie Hubler, artist, inventor of washable fabric photo frames, author, product / surface / textile / fabric / pattern designer of patterns and printables, sewing projects such as house shape potholders, dog clothes and diapers for Yorkies and pugs, cards, calendar sheets, owner of fabricatedframes.com fabricatedframescom@gmail.com https://zazzle.com/store/fabricatedframes/products