Sleepy Hollow Art Frame Ornament For 2x3 Photo Poster

Sleepy Hollow Illustration Art Frame Ornament For 2x3 Photo Papercraft Printable Sleepy Hollow Illustration Art Inside Picture Frame Ornament For 2x3 Photo Pattern Paper Crafts Printable This DIY printable, that you download and print with your inkjet printer, letter size, you can make a table standing picture frame / ornament, and has my illustration art, inspired by Sleepy Hollow, where Ichabod Crane nervously exchanges pumpkin pie for the Headless Horseman's pumpkin. The Headless Horseman is riding his noble horse Daredevil, both about to approach a covered bridge, and under a harvest moon, with cattails knocking against a log near a brook and tree.. It's my unadulterated take on this classic story by Washington Irving! My way of putting a softer approach to artistically showing the story. lol Once made, the Sleepy Hollow art will show through the picture window, shown and printed on panel 3, top right corner. Show the Sleepy Hollow art on display in your room, on your desk, on an ornament tree, use as a Halloween party favour, decoration, or insert your own photo or art 2x3" in size! This download printable is a papercraft, a DIY pattern that makes a 3x4 tabletop picture frame, for a x2x3 inch photo, with bendable strut leg, and can turn into a hanging ornament! SUPPLIES: Note: make sure that all supplies are labelled acid free and/or photo safe - all supplies sold in art or craft stores, office supply, or big box stores in stationery / scrapbook and/or fabric / crafts / paper / architectural tools area 1 letter size sheet of any of these: inkjet paper - card stock paper - washable inkjet fabric - self laminating sheet optional for paper - any inkjet printable substrate (surface) 2 ribbons: one 1/8" or 3 mm wide by 2 feet long to thread through 7 circles hole punched on panels 2 & 3, thread in both directions to join and make photo pocket - one ribbon 1" wide by 6" long to connect optional given strut leg to easel back, if wanting to stand frame on table or shelf letter size sheet protector page: cut to size of photo for protective photo sleeve - also used with strut leg clear piece pattern, sandwiched between front & back strut legs, split into top & bottom, shows through middle to make strut leg bend, to pitch for frame to stand - acid free / photo safe labelled and found in Walmart, Walgreens, Target, scrapbook section, office supply, or online INSTRUCTIONS: Print on inkjet printable surface Cut out panel parts labelled, cut along lines printed, cutting into and away inner and outer corners along lines - trim away excess white negative space on sheet Fold side flaps under and glue / tape down on back along outer / inner edges Hole punch all circles Connect panels 2 & 3, print sides facing into each other by threading skinny ribbon through 3 sided 7 holes in both directions, knot on both sides, trim ribbon tails, glue down Assemble and glue panels together, front or 1 on top of 2, and 4 on top of 3, gluing between spaces between holes along outer inside edge - leave opening on bottom right corners, both sides, for ribbon to be tucked in, connecting bottom right of strut leg STRUT LEG: Make sure both top and bottom of both front and back strut leg panels are cut out, side flaps in tact, separated along lines, white negative space removed, flaps folded under, and cut clear strut leg piece from pattern provided Back strut leg top & bottom facing down, sides folded in glued down or open, place clear strut leg on top, using very close spacing between top and bottom, spacing about 1/16" to 1/8" between top and bottom back strut leg panels - can fold and glue down flaps over clear strut leg piece or not - your choice Add ribbon along inside of vertical side of bottom strut leg on back or inside - it will hide inside between the back and front bottom strut leg Place and glue down front strut leg panels, top and bottom Align bottom right strut leg and easel back corners CAREFULLY, PATIENTLY, and GENTLY, while holding - use table or flat surface to help tap in place - flip top strut leg out, and gently place glue on inside top part of back strut leg. Press onto easel back Stand frame, pulling ribbon out front, under bottom of frame. Pitch strut leg out, pulling the ribbon towards back, mark with a pin or tape or a safety pin where the ribbon meets the bottom of the frame, and trim ribbon down to 1-2" in front Tuck ribbon inside bottom right area between easel back and inside panel 3, stand frame, pitch strut leg, and where it stands on it's own, gently mark where ribbon stopped, and add glue inside, press closed Cut protective photo sleeve from sheet protector the size of the photo Add optional ribbon through hole on top of back panels 3 & 4, to hang as an ornament OR Add optional military clutch, in top hole on back, to wear as a badge / pin / brooch costume jewellery, or chain to wear as a pendant / badge Place photo in photo sleeve, and then place inside the frame, and display it! Thank you! Kristie Hubler artist, author, inventor of washable fabric photo frames, the convertible frame pin ornament, plus sewing patterns for house shape kitchen potholders, pug & Yorkshire terrier dog diapers and clothes, printables for cards, calendar sheets, tags, and other crafts, clock tell time / colour wheel fidget spinner sensory education toy, math and writing printables, also buy the downloadable "Fabric Font", in my store, and install on your device's apps that change the font, then type or write away, with my textile / sewing themed font, simulated lengths of fabric, folded and draped to form all the alphabet, numbers, 94 keys on keyboard, space bar, plus 20 symbols, 110 characters in all, owner of fabricatedframes.com fabricatedframescom@gmail.com https://teacherspayteachers.com/store/fabricated-frames